Wayne WLS75 Instructions d'exploitation télécharger pdf

Lawn

Sprinkler

Pump

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or prop-

erty damage! Retain instructions for future reference.

Description

This pump is a high capacity, self-prim-

ing centrifugal pump suitable for lawn

sprinkling or other applications where

large quantities of water are required.

Flammable liquids such as gasoline,

chemicals or corrosive liquids should

never be used with this pump.

Safety Guidelines

This manual contains information that

is very important to know and under-

stand. This information is provided for

SAFETY and to PREVENT EQUIPMENT

PROBLEMS. To help recognize this

information, observe the following

symbols.

Danger indicates

an imminently haz-

ardous situation which, if not avoided,

will result in death or serious injury.

Warning indicates

a potentially haz-

ardous situation which, if not avoided,

could result in death or serious injury.

Caution indicates a

potentially haz-

ardous situation which, if not avoided,

may result in minor or moderate injury.

Notice indicates

important informa-

tion, that if not followed, may cause

damage to equipment.

General Safety Information

1. Read these rules and

instructions carefully.

Failure to follow these

instuctions could

cause serious bodily

injury and/or property damage.

NOTICE

Operating Instructions and Parts Manual WLS Series

This pump is non-

submersible.

Pump only clear water. Do

not pump flammable or

explosive fluids such as

gasoline, fuel oil,

kerosene, etc. Do not use in a flamma-

ble and/or explosive atmosphere.

Personal injury and/or property dam-

age could result.

This pump is not

designed to handle

salt water, brine, laundry discharge or

any other application which may con-

tain caustic chemicals and/or foreign

materials. Pump damage could occur if

used in these applications and will

void warranty.

All wiring must be per-

formed by a qualified

electrician. The pump

must be installed in com-

pliance with all local and national

codes.

2. Connect this product to a grounded

circuit equipped with a ground

fault interruptor device.

3. Before installing this product, have

the electrical circuit checked by an

electrican to ensure proper ground-

ing.

4. BE CERTAIN the pump

power source is dis-

connected before

installing or servicing

pump.

5. Check motor voltage setting on

motor endplate and make sure the

line voltage of the electrical current

supply is correct.

6. Be sure the water source and piping

is clear of sand, dirt and scale.

NOTICE

320200-001 6/98

Debris will clog pump and void war-

ranty.

7. Failure to protect pump and piping

from freezing could cause severe

damage and will void the warranty.

8. Do not run pump dry. Follow prim-

ing instructions.

Installation

Protect pump from the elements by

installing in a basement, garage, tool

shed or pump house. Install the pump so

the centerline of the pump is as close as

possible to the water level. Keep installa-

tion area clear to provide access for ser-

vice and maintenance. Protect the pump

against flooding and excess moisture.

Make sure the pump has adequate ven-

tilation. The surrounding temperature

should not exceed 100

F (38

C) or nui-

sance tripping of the motor may occur.

PUMP PIPING INSTALLATION

Use new pipe for best results.

Galvanized or plastic pipe can be used.

When using galvanized pipe, provide

independent supports for both suction

and discharge piping near the pump to

avoid strain on the pump. Minimize use

of elbows and fittings to reduce friction

loss. Refer to the friction loss chart for

specific information.

Increase diameter of suction or dis-

charge piping if length is over 50 feet.

SUCTION PIPING

Install foot valve

or strainer screen

over intake of suction piping.

Never use pipe smaller than 2” in

diameter for suction piping. The suc-

tion pipe must be kept free of air leaks.

MANUAL

1 2 3 4 5

Résumé du contenu

Page 1 - Sprinkler

LawnSprinklerPumpPlease read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product descr

Page 2 - Lawn Sprinkler Pump

2Operating Instructions and Parts ManualInstallation (Continued)For horizontal runs, lay pipe from thewater source so the upward slope is atleast 1/2”

Page 3 - WLS Series

OperationNever run the pump dry. Runningpump without water may cause sealdamage. Fill the pump with waterbefore starting.PRIMING THE PUMPAfter pump in

Page 4

Operating Instructions and Parts ManualLawn Sprinkler Pump4Maintenance (Continued)DRAINING FOR WINTERAlways protect pump and pipingagainst freezing te

Page 5

1234568791011Operating Instructions and Parts Manual1 Motor 32031-001 32015-001 32020-001 32021-001 12 3/8”-16 x 1” Hex cap screw 16334 16334 16334 16

Commentaires sur ces manuels

Pas de commentaire

Wayne WLS75 Instructions d'exploitation

Naviguer en ligne ou télécharger Instructions d'exploitation pour Non Wayne WLS75. Wayne WLS75 Operating instructions Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non Wayne WLS75