Wayne PC1 Manuel d'utilisation et d'entretien télécharger pdf (Page 2)

Models PC1 and PC2 include a six foot

long suction hose, a water suction

attachment, and a replacement parts kit

which includes: impeller, gasket, shaft

seal, and two motor brushes (PC2 only,

brushes are not designed to be replaced

on PC1).

Always disconnect power source

before attempting to install, service,

or maintain the pump. Never handle a

pump with wet hands or when standing

on wet or damp surface or in water.

Fatal electrical shock could occur.

1. A ground fault circuit interrupter

(GFCI) is required for Model PC2.

Risk of electrical shock! This pump is

supplied with a grounding conductor

and grounding type attachment plug.

A grounded receptacle in conformance

with current NEC and local codes must

be used (See Figure 1). Do not use

model PC2, 115 V Transfer Pump in

swimming pool areas.

2. Model PC1 operates on 12V DC only.

Model PC2 operates on 115V only.

Voltage and current of power supply

must match the requirements of the

pump. Model PC1 has color-coded

battery clamps for 12V operation.

Model PC1 requires 14 amps at 12

VDC.

3. Never use an extension cord to

power this unit.

Risk of fatal electrical shock. Never

cut off the round grounding prong.

Cutting the cord or plug will void

the warranty and make the pump

inoperable.

4. Use a strainer when pumping from a

creek, pond, or source where foreign

objects may be sucked into the

pump. The strainer should prevent

solids from entering the inlet line.

5. A regular garden hose may be used

as a discharge line.

6. The inlet or suction hose should

not be longer than 15 feet; and

the vertical distance between the

pump and the water level should

not be any higher than 10 feet. The

maximum discharge height is 30

feet.

7. At times, an overload due to

overheating, low voltage, jammed

impeller, etc. may shut the pump off.

Unplug or turn off the pump and

wait at least ten minutes. The pump

will cool and automatically reset.

(Model PC2 only)

8. Motor should never be operated

for more than 2 hours continuously.

Critical heating can occur and might

severely damage the pump and void

warranty.

Operation

1. Add 1 tablespoon of vegetable oil

to both inlet and outlet to prime.

Attach included 6 foot suction hose

to inlet of pump. Attach garden

hose to outlet of pump. There

must be a gasket in place to insure

that these connections are airtight,

otherwise the pump will not prime.

2. Connect water suction attachment

to the open end of inlet hose and

place below water surface. (Water

suction attachment is optional

for both PC1 and PC2 models.)

The water suction attachment is

designed to fit the male end of

a garden hose. Place the water

suction attachment as near as

possible to the middle of the water

that is to be pumped.

3. Examine the inlet and outlet hoses

to insure there are no blockages,

kinks or bends.

Place switch in

“OFF” position

before connecting or disconnecting

battery terminal clamps.

Operating Instructions and Parts Manual

www.waynepumps.com

Installation

IMPORTANT BATTERY

INFORMATION

Be certain that the area around the

batteries is well ventilated. Before

servicing the batteries, blow away

gasses by waving a piece of cardboard

near the batteries.

Dangerous

hydrogen gas

can be released from batteries while

charging. Sparks can ignite the gas

in an enclosed space. Wear safety

goggles when connecting batteries.

Battery connections should be made

in a well-ventilated area.

Working in the

vicinity of lead

acid batteries can be dangerous.

Before making connections or

servicing the batteries, read and

follow instructions in all applicable

instruction manuals. To reduce the

risk of battery explosion, follow

the instructions in this manual and

those published by the battery

manufacturer, as well as those of

any other equipment used in the

surrounding area.

An assistant should be present or

close enough to come to your aid in

the event of an emergency. Have a

reliable source of fresh water and

soap nearby in case battery acid

contacts clothing, skin or eyes.

Wear eye and clothing protection

when working around lead acid

batteries.

Avoid touching your eyes when

working around lead acid batteries.

If battery acid

contacts your

eye(s), ﬂush with cold running

water for 20 minutes and seek

immediate medical attention. If acid

contacts your skin or clothing, wash

immediately with soap and water.

Never smoke or

allow a spark or

ﬂame in the vicinity of the battery.

Avoid dropping

metal tools on

the battery posts because they may

spark or short-circuit the system or

battery, causing an explosion.

1 2 3 4 5 6 7 8

Commentaires sur ces manuels

Pas de commentaire

Wayne PC1 Manuel d'utilisation et d'entretien Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Pompes à eau Wayne PC1